Sold: Valmet Parts. HGs, PG, US Stock, Etc. Updated.

Place to buy and sell your parts and accessories!

Moderator: AGG

Post Reply
762AP
Posts: 161
Joined: Wed Jan 21, 2004 8:30 pm
Location: Oregon.

Sold: Valmet Parts. HGs, PG, US Stock, Etc. Updated.

Post by 762AP » Wed Mar 09, 2016 5:11 pm

Parts only available in the US, no shipping outside US borders.
Selling the last Valmet parts from a Norinco Hunter conversion.
Pic of completed project.
Image

I accept MO or check, no paypal.
Parts are listed on other sites.
Post "I'll take it", then IM.
Shipping extra.

SOLD
2 pistol grips and 1 set of hardware.
The one on the left is a SAKO M-95, fatter than standard, one on the right is a used and abused Valmet M-76. Had extra holes drilled in at bottom, filled with JB Weld and painted.
The mounting hardware is Valmet, the bolt had a screwdriver slot ground into it for mounting on the Hunter conversion. $60 for all three pieces pictured.
Image
Image



SOLD
Set of Valmet HGs and mounting hardware.
HGs were NOS when I received them.
One small inlet on each, allows the modified AR15 front HG cap to retain them.
Also includes a modified Saiga lower HG botl on unit and a Valmet M-76 rear HG cap.
$120 for the parts pictured.
Image
Image
Image
Last edited by 762AP on Mon Jul 11, 2016 4:09 am, edited 5 times in total.

E. Blake
Posts: 308
Joined: Fri Oct 08, 2004 11:40 pm

Nice job

Post by E. Blake » Sat Mar 12, 2016 6:10 am

Brother,

I am sure you have good reasons for parting out your rifle, but I just want to say that the project as you originally finished it was a very well-done job. Whoever bought your barreled receiver should've just talked you out of the whole enchilada!

Good luck with whatever "the next thing" is.

E.

E. Blake
Posts: 308
Joined: Fri Oct 08, 2004 11:40 pm

bolt carrier and piston and gas tube

Post by E. Blake » Thu May 05, 2016 10:03 am

If the bolt carrier and piston and gas tube are still available, I'd be interested. LMK via this site or e-mail me at wynbryant01@gmail.com.

Thanks!

Wyn (E. Blake)

M62/M76
Posts: 428
Joined: Sat Oct 08, 2005 12:30 pm
Location: Washington State

Post by M62/M76 » Fri May 06, 2016 6:31 am

I think, what he is saying is,
his project is complete and these parts are extras for sale.
The conversion looks nice!
Need a flash hider on there!

762AP
Posts: 161
Joined: Wed Jan 21, 2004 8:30 pm
Location: Oregon.

Post by 762AP » Fri May 06, 2016 4:24 pm

No, I had to part it out. Medical bills and the like...... :(
Appreciate the comment. I do miss it, but knowing E. Blake is getting some of it, it's not over, just being recycled!

E. Blake
Posts: 308
Joined: Fri Oct 08, 2004 11:40 pm

Post by E. Blake » Fri May 06, 2016 6:06 pm

I will post pix of the parts installed in their new "home."

Best,

E.

E. Blake
Posts: 308
Joined: Fri Oct 08, 2004 11:40 pm

new parts installed

Post by E. Blake » Thu May 19, 2016 1:45 pm

As promised.

I think it looks kind of cool with the bolt carrier still in the white; I may just leave it as it is.
:D

Image[/img]

M62/M76
Posts: 428
Joined: Sat Oct 08, 2005 12:30 pm
Location: Washington State

Post by M62/M76 » Thu May 19, 2016 4:33 pm

Looks Good! 8)

E. Blake
Posts: 308
Joined: Fri Oct 08, 2004 11:40 pm

Post by E. Blake » Thu May 19, 2016 7:46 pm

Thanks!

762AP
Posts: 161
Joined: Wed Jan 21, 2004 8:30 pm
Location: Oregon.

Post by 762AP » Sat Jul 09, 2016 3:18 pm

PGs and HGs with hardware still available.

Post Reply